The season has come to an end and now you are faced with the arduous task of cleaning up you maple operation. Where do you start and what do you use? For most equipment, the answer is simple – lots of hot water and elbow grease. A good place to start is with the tanks that hold both sap and syrup. Most are stainless steel and are easy to clean with a pressure washer. We found that a tank washing nozzle that fits your pressure washer is a valuable tool. The specially-designed nozzles enable you to spray to the side and reach areas that a standard spray tip cannot reach. There is no substitute for stainless steel equipment if you can afford it.

Plastic totes and poly tanks have become popular because they are relatively inexpensive but they are harder to clean. Plastic totes, while affordable, may only last about two or three seasons if you get off your cleaning schedule. It does not take long for the plastic to become so contaminated with bacterial spores that you have to discard and replace. However, if you keep poly tanks cleaned they will last for years. Another simple tip is to clean as soon after the season ends as possible. Allowing totes and tanks to sit dormant allows bacteria to build and grow making cleaning more difficult.

Your evaporator needs to be sugared off and flushed out as soon as possible. I often flush the pans with clean water and then refill them with permeate from the RO and let them soak. If permeate is not available, use water. I will drain and refill the pans with clean water and then add the proper amount of pan cleaner following label directions. Once the pan cleaner has done its job, I drain the pans and use a high pressure washer to finish the job. Do the process correctly and your pans will look brand new. Make sure all your float boxes are clean, replace gaskets if needed. Soak your auto draw off temperature probe and your hydrometer in a 5% vinegar solution to remove any residues or films. The thermocouple in the auto draw off probe works best when there is no niter on the probe. Clean your filter press thoroughly and lubricate parts with a food grade lubricant. It is good practice to remove all extra filters from your sugarhouse and store them in your house, somewhere dry and rodent-free. If you use a filter tank, you will need to clean filters and make sure they are completely dry before story to ensure no mold will develop over the off-season. Any filters with problems, even minor, should be discarded, and you should purchase new inventory for the next season.

Reverse osmosis units (RO) should be soap washed and thoroughly rinsed immediately after the last time you use them. Make sure all of the permeate is drained out. Once you break down the RO, return your membranes to the storage vessels with a cup of permeate in each one. Once everything is clean, you should send the membranes in to your dealer for cleaning and testing. There is nothing worse than starting a season with a bad membrane that is passing sugar. Make sure your high pressure pump and your feed pump are free and fully drained. Inspect the membrane housings and get them as dry as possible. Many times with the recirculating motors and pumps on the bottom of the membrane towers, dampness can cause the pump shafts to seize and seals to deteriorate. Because evaporators and ROs require the use of chemicals that are incompatible – phosphoric acid and basic soap – keep them separate and out of reach of children. Be careful when you mix pan cleaner and always follow the directions on the label.

The most controversial portion of a maple system to clean is most certainly the tubing. It seems everyone has his or her own way of dealing with the miles of tubing stretching through the woods. I have cleaned tubing just about every way possible over the years. We have sucked water, pumped water and air, water only, air and tubing cleaner, and just plain did not clean at all. In my experience, using water and air worked well until we tried to pump up too steep of slope and had a blowout that may have had enough force to launch a satellite. Sucking water through the lines left a lot of liquid in the lines that eventually turned to green snot. The method we now use seems to work. We pull taps with the vacuum, nip off each old spout, and immediately use a Stars Company (out of Quebec) line plug to seal the drop line and maintain vacuum on the system. Done properly, the sap in the lateral line will not suck back into the drop line. We then use a paint marker to mark the old tap hole which greatly speeds up next season’s tapping process. Once all of the taps are out, we back flush the mainlines with clean water. Next we close all of the main lines and open the end of each lateral opening long enough to pull air through the lines and keep vacuum on the system. Doing this should remove 80% of the liquid from the lateral and main lines. At this stage, we successively open the ends of each main line and let air in with the vacuum on. Once the vacuum on the entire system drops to zero shut off the pump. At some point before the next season, we then install new spouts on all the drops and let the lines air out completely. This method may seem excessive but it does work. We have a small amount of green sap at the start of the season, but nothing we could not easily filter and could possibly have been avoided by flushing the system again before the season.

A word of caution when it comes to using tubing cleaners. They have to be completely flushed from the lines before the next season. Never use Isopropyl alcohol – it is illegal in the United States. Also be aware that some cleaners attract Mr. Bushy Tail and his friends – never a good thing for tubing operators.

Once your system is cleaned, bring in all releasers and clean and sanitize them thoroughly. They are made of PVC which makes a good home for bacteria. Go over the mechanism and use lubricant provided by the manufacture to lubricate all of moving parts. The last task is to care for your vacuum and transfer pumps. Change the oil or drain out the water on liquid ring pumps. On the new rotary claw pumps change the oil and fog the pump with a pump oil. You need to make sure rust does not build up. The same is true for rotary vane pumps which are more maintenance-free but putting some oil on the vanes never hurts. All gasoline motors should be drained and the gasoline replaced with SeaFoam or a similar product. Never leave gas with ethanol in the tank. Drain the crank case oil and replace it with fresh motor oil and you will be ready to go for next season. Lastly, make sure you transfer pumps are drained and stored somewhere that will not fall below freezing.

Author: Les Ober, Geauga County OSU Extension